How much water comes out of a firefighter hose?

A 100-foot length of 400 PSI 1 1/2-inch double-jacket hose by Superior Fire Hose weighs 29.6 pounds dry. This hose flows roughly 150 gallons per minute.

What is the flow rate of a fire hose reel?

The minimum flow rate of hose reels in JET and SPRAY setting at 220 kpa pressure; for 13mm nozzle is 0.24 L/S, for 19mm nozzle is 0.45 L/S and for 25mm nozzle is 0.55 L/S. The effective throw range of discharge at 0.2 MPa (2 bar) pressure is 10 mtrs.

How much water is in a 3 inch fire hose?

3-inch hose—water content—per foot of length 0.367 gal. 2 1/2-inch hose—water content—per foot of length 0.255 gal. One 50 ft. length 3-inch hose—contains 156 pounds of water One 50 ft.

How many Litres per minute does a fire hose use?

Designed for: Fire hose reels are designed to deliver a minimum of 20 liters of water per minute. Lengths: A fully extended fire hose is normally between 30 and 36 meters. Used for: They are located to provide an accessible and controlled supply of water to combat a potential “Class A” fire risk.

IMPORTANT:  You asked: How much space should be in front of fire extinguisher?

What is the maximum distance between fire hose reels?

Fire Hose Reels are easy to use, provide a virtually unlimited supply of water, as they are connected to the mains water supply, and should extend for approximately 35 metres.

How much does 1.75 fire hose weigh?

While it depends on the materials used to make the hose, the average weight of a hose of this diameter is 0.34 pounds per foot (or about 20 pounds per 50 feet of length).

How do I calculate how much water is in my hose?

To find the volume of the hose, first convert the length to inches as well. You want compatible units when multiplying area by length to get a volume. The length in inches is of course 1200 inches, so when you multiply that by the area of the circle, you get the volume of water in the fire hose.

What pressure is a fire hose?

To fight a fire on the ground, a fire hose needs about 150 pounds per square inch of water pressure. To get water to the 30th floor of a building, the pressure needs to be about 300 PSI to offset the effects of elevation.

How much friction do you lose in a fire hose?

Friction losses on reeled hose average about 21 percent more than for straight hose lays. Friction loss is nearly independent of pressure. Friction loss varies with type, lining, weave, quality, and age of the hose. Friction loss increases 4 times for each doubling of water flow.

How do you calculate friction loss in a fire hose?

The process of calculating friction loss in 2½” hose is accomplished by figuring the friction loss as you would for 3” hose and then doubling the result. For example, if the flow in 100 feet of 3” hose is 300 gpm, then the friction loss is 9 psi per 100′. Next, double 9 to obtain the answer of 18 psi per 100 feet.

IMPORTANT:  You asked: What does it mean when fire trucks are on bridges?

Is a fire hose always charged with water?

Is a fire hose reel always charged with water? … Fire Hose Reels are easy to use and provide a virtually unlimited supply of water, as they are connected to the mains water supply, and should extend for approximately 35 metres. Fire Hose reels consist of a length of non-kinking tubing.

Where should fire hose be placed?

Where fire hose reels are to be located

  • Fire hose reels must be located within 4m of an exit. …
  • Generally, separate hose reels are to be provided for each storey of the building. …
  • A fire hose reel should not be located such that it is required to take the hose through a fire or smoke door to fight a fire.
Fire safety